A pipe freezes where a supply line runs through space the heating does not reach: a crawl space, an outside wall, a garage, an unheated basement corner. Ice splits the line while nothing comes out of the tap, so the flooding begins at the thaw, often in an empty house, and that is the moment worth planning for.
Key takeaways
- Freezing happens in unheated runs, so the vulnerable pipes in any house are the ones furthest from the heat and nearest the outside air.
- A split line leaks nothing while it is still frozen, which is why a frozen tap is a warning rather than a nuisance.
- Knowing where the main shutoff is, and which way it turns, is the single most useful thing to learn before a cold snap.
- Thawing a pipe with an open flame is the mistake that turns a plumbing problem into a fire.
- A house left empty in winter is the classic setting, because nobody is there when the water starts.
- Kokomo's median build year is about 1967 by one estimate, and older houses tend to have more unheated pipe runs than new ones.
Which runs of pipe freeze, and why those?
The ones outside the heated envelope. A line crossing a vented crawl space, a pipe inside an exterior wall with little insulation behind it, a run through an unheated garage or porch, a hose bib left connected, and the feed to an outside tap are the usual candidates.
Heat reaches a pipe by conduction from the material around it and by the air in the space it sits in. A line in a wall cavity with cold air leaking into it at the sill plate is in colder air than the room on either side, which is how a pipe in a heated house freezes anyway. The temperature at the pipe, not the thermostat reading, is what decides.
That is also why the same house can lose a different pipe each time. Wind direction, a vent cover that blew off, a crawl space door left open and a garage used with the door up all change which run is coldest. A plumber looking at a house after one freeze will usually point at two or three others worth protecting.
Does the age of a Kokomo house matter here?
It tends to, because of how the building is put together rather than the age of the pipe. By one third-party estimate the median build year in Kokomo is about 1967 and roughly a fifth of the stock predates 1940, and older houses more often have plumbing routed through unheated space.
A crawl space with open vents, a basement with a cold outside corner, a kitchen addition built onto what used to be an outside wall: each of those puts a supply line somewhere a modern layout would not. Later remodels add to it, because a bathroom pushed into a former porch takes its plumbing with it into a thinly built wall.
None of that means an older house is bound to lose a pipe. It means the vulnerable runs are worth finding on a mild day, with a flashlight, before the weather does the finding. Pipe insulation on an exposed run is cheap, and knowing which cabinet doors to leave open costs nothing at all.
What are the signs that a pipe has already frozen?
A tap that gives nothing, or a trickle that dies, while other taps in the house run normally. Frost or condensation on an exposed pipe. A toilet that will not refill. Sometimes a faint knock from the wall as ice moves inside the line.
Work out which fixtures are affected, because the pattern points to the run. One cold tap on an outside wall suggests a local freeze; everything beyond a certain point in the house suggests the problem is further back. If nothing anywhere runs, the freeze may be at the service entry, which is a different and larger conversation.
Treat a dead tap in cold weather as urgent rather than as something to wait out. A pipe that froze once has usually been close to freezing several times, and the damage that shows up is the cumulative result. Our frozen pipe thaw damage page covers what happens when the ice finally lets go.
What should be done while the pipe is still frozen?
Find the main shutoff and be ready to close it. Open the affected tap so meltwater has somewhere to go. Warm the space the pipe runs through rather than attacking the pipe itself. And keep someone near the fixture while it thaws.
Opening the tap matters more than it sounds. It relieves pressure as the ice gives way and it tells you the moment water starts moving, which is also the moment any split begins to leak. If water arrives and then keeps arriving somewhere it should not, closing the main is a two-second job for anyone who already knows where the valve is.
Warming the space is the safer approach: raise the heat in the room, open the cabinet doors under a sink on an outside wall, put a safe electric heater into a cold basement corner at a distance from anything that can burn. Slow warming of the surrounding air is less likely to crack a fitting than concentrated heat on one spot.
Why is a flame the wrong tool?
Because a blowtorch on a pipe in a wall or a crawl space sets the structure alight, and because it heats one point so quickly that the fitting next to it can fail. House fires caused by thawing pipes are a recognized hazard in the trade, and the method has no advantage worth the risk.
The materials around a pipe are the problem: old framing, paper-faced insulation, dust in a joist bay, a vapor barrier in a crawl space. None of it needs much encouragement, and a fire behind a wall is well established before anyone in the room knows about it. The same objection applies to any device with an open flame pressed into a confined space.
Heat guns and hair dryers are not the same thing as a flame, but they still concentrate heat and still need watching. If a pipe is somewhere you cannot see, or the fixture it serves is behind finished surfaces, that is the point to stop and call a plumber rather than to try harder with the tool in hand.
Why does the flooding start at the thaw?
Because ice is a plug. A line can split along a seam while it is frozen and lose nothing at all, since the ice both caused the split and is blocking it. When the ice melts, the pipe is open, the supply is still pressurized, and water runs until someone closes a valve.
This is the detail that catches people out. A homeowner who runs a tap, gets nothing, and then finds it running again the next afternoon reasonably assumes the problem has resolved itself. In fact the test is not whether water comes out of the tap. It is whether the meter keeps turning with every fixture closed, and whether anything downstairs has become damp.
Where a house has been unoccupied through a cold spell, the first visit should include a look at the ceiling below every bathroom and kitchen, the basement or crawl space, and the meter. A split that let go three days earlier has had three days to soak a floor structure. The burst pipe water damage page covers what that looks like.
What does a crew do with a pipe loss in a wall or a crawl space?
Isolate the supply, read the moisture through the wall and the floor to find the extent, open the cavity where the readings require it, remove insulation that held water, and then dry the framing and the remaining board to measured targets. The pipe repair is a plumber's.
Water from a pressurized line behaves differently from flood water: it arrives clean and in volume, and it travels along framing and under flooring rather than pooling where it entered. A reading taken two rooms away is therefore not a waste of time, and that is why the first walkthrough covers more of the house than the obvious damp patch.
Crawl spaces need their own treatment, because water sitting on a vapor barrier does not drain and the space is often too tight for ordinary equipment placement. Insulation under a floor comes out when it has held water. Our crawl space and basement moisture page goes through it.
What is worth doing before the next cold spell?
Locate and label the main shutoff and test that it turns. Disconnect garden hoses. Insulate exposed runs in crawl spaces and garages. Close crawl space vents if the system is designed to allow it. And decide what happens if the house is left empty.
The empty-house question is the one most often skipped. If nobody will be in the building for a stretch of cold weather, either leave the heating on at a reasonable setting and have someone look in, or shut the water off at the main and drain the system. Half measures, such as turning the heat right down and hoping, are how the worst of these losses happen.
Phones are answered at any hour and a crew goes out as soon as one is free, with no arrival time promised. Call (833) 490-5225 when water is running and say which fixture it came from and whether the main is closed. The contact page lists the other details worth having to hand on that first call.
Frequently asked questions
A tap stopped running in the cold. Is that an emergency?
Treat it as one. The pipe may already be split, and you will not know until it thaws. Find the main shutoff now, open the affected tap so meltwater can escape, warm the space the pipe runs through, and have someone near the fixture as it comes back. If water starts going somewhere it should not, close the main.
Can I thaw it myself?
You can warm the space around it: raise the room heat, open cabinet doors on outside walls, use a safe electric heater at a distance in a cold basement. Do not use anything with a flame, and do not keep working at a pipe you cannot see. A line inside a wall or under a floor is a plumber's job.
Why did it flood after the weather warmed up?
Because the ice that split the pipe was also blocking it. Once it melts the line is open and still under supply pressure, so water runs until a valve is closed. That is why a thawed tap is not proof the problem has passed; the meter and the ceiling below are the better test.
Does the drying work include fixing the pipe?
No. A crew isolates the water where it can, reads the wet area, opens what has to be opened, removes material that will not dry and dries the structure to target. The pipe repair is a plumber's work and is quoted separately, as is the carpentry that puts the wall back afterward.
How long will a wall take to dry after a pipe loss?
It depends on the materials and the readings rather than the calendar. Framing lumber and plaster give up moisture slowly, while thin board and insulation respond faster or come out entirely. The guide on knowing when a house is dry explains what the readings have to reach.
Sources
This guide is general information for Howard County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.